kW vs kWh in Commercial Battery Storage: What Irish Businesses Actually Need to Know
Get kW and kWh wrong and you either overspend by 40% or buy a battery that cannot deliver the peak shave you bought it for. Here's how to size both correctly for Irish commercial sites.
By Smart Solar Editorial · Updated 15 May 2026 · 8 min read

If you read one technical concept about commercial battery storage in Ireland before signing a quote, make it this one. The difference between kW and kWh is the single biggest source of mistakes in commercial BESS procurement - and the easiest way for an under-qualified supplier to oversize or undersize a system by 40%.
kW is power. kWh is energy.
Think of a kettle. A 3 kW kettle pulls 3 kW of power while it is running. If it runs for one full hour, it consumes 3 kWh of energy.
Apply that to a battery:
- kW is the rate at which the battery can deliver or absorb power. It is set by the Power Conversion System (PCS), also known as the inverter.
- kWh is the amount of energy stored in the cells. It is set by the number of battery modules.
A commercial BESS is described by both numbers together: a "500 kW / 1,000 kWh system" has a 500 kW PCS and 1,000 kWh of usable energy. At full power, it will discharge for 2 hours (1,000 / 500). Engineers call this the duration - in this case, a 2-hour battery.
Why this matters for Irish business cases
The kW figure determines what peak demand you can shave. The kWh figure determines how long you can shave it for.
Take a real Irish example - a mid-size Cork engineering plant with a 750 kVA MIC, a 12-month profile peaking at 720 kW for 90 minutes between 17:00 and 18:30 on winter weekdays.
If you size the battery as 300 kW / 300 kWh (1-hour duration):
- You can shave 300 kW of peak. New peak = 420 kW.
- But you can only hold that shave for 1 hour. The remaining 30 minutes of the 90-minute peak event will not be covered, so your billable demand may still hit 720 kW.
If you size as 300 kW / 600 kWh (2-hour duration):
- Same 300 kW shave, held for the entire 90-minute event with margin.
- New billed peak = 420 kW, MIC can be reduced to ~450 kVA, saving roughly €60k per year at €150/kVA.
The energy (kWh) side doubled the cost of cells but unlocked the full peak-shaving value. The power (kW) side stayed the same.
How C-rate ties kW and kWh together
C-rate is the ratio of power to capacity. A battery with a 1C rate can fully discharge in 1 hour. A 0.5C battery takes 2 hours. A 2C battery does it in 30 minutes.
For commercial Irish applications:
- Peak shaving and self-consumption: 0.25C-0.5C is standard (2-4 hour batteries). Long duration matters more than fast power.
- DS3 frequency response: 1C-2C is typical (30-60 minute durations). Fast response, short bursts.
- Backup power / UPS replacement: 0.5C-1C depending on critical load profile.
Most Irish commercial BESS in 2026 are 0.5C to 1C systems - a 500 kW PCS paired with 500-2,000 kWh of LFP cells, giving 1-4 hours of duration.
The procurement trap: matching kW to kWh
A common mistake is buying a "1 MWh battery" without nailing down the PCS sizing. Vendors selling on price often pair 1 MWh of LFP cells with a 250 kW PCS to hit a low headline number - giving a 4-hour battery. That is fine for solar self-consumption but useless if your business case is MIC reduction during a 90-minute evening peak that needs 800 kW of shave.
Conversely, oversizing the PCS (e.g. 1 MW PCS on 500 kWh of cells, a 2C battery) wastes capex on inverter capacity you will never use unless you are chasing DS3 fast frequency response - and pushes the cells through deeper, faster cycles that age them quicker.
How Irish suppliers quote it
When you receive a quote from Activ8 Solar Energies, Enerpower, Powerlink or any other Irish EPC, look for these line items:
- PCS rating in kW (e.g. "Sungrow PowerStack SC500-HV, 500 kW")
- Usable energy in kWh at end of warranty (e.g. "966 kWh usable, 1,032 kWh nameplate, after 10 years / 6,000 cycles to 80%")
- Maximum continuous C-rate (e.g. "0.5C continuous, 1C peak for 15 minutes")
- Round-trip efficiency at 0.5C (e.g. "AC-AC RTE 88%")
If any of these four are missing, ask. A complete quote names both kW and kWh and tells you the C-rate. A vague quote that says "1 MWh BYD battery" is a red flag.
Worked example: data centre DRUPS replacement
A 4 MW Irish data centre wants to replace ageing diesel rotary UPS (DRUPS) with a lithium BESS that doubles as a peak-shaving asset.
Critical IT load: 2.8 MW continuous. Backup window required: 8 minutes (to start generators). Daily peak shave opportunity: 600 kW for 90 minutes against a €175/kVA capacity charge.
Sizing logic:
- PCS: must cover 2.8 MW critical load instantly. Spec 3 MW PCS, grid-forming, with seamless transfer.
- kWh for backup: 2.8 MW for 8 minutes = 374 kWh. Add 20% headroom = 450 kWh.
- kWh for peak shave: 600 kW for 90 minutes = 900 kWh. Add 15% degradation buffer = 1,035 kWh.
- Total: 3 MW / 1,035 kWh, with the 450 kWh always reserved for islanding.
The same PCS does both jobs. The cell stack is sized for the larger of the two energy demands. Total installed cost in 2026 lands around €1.8M-€2.2M, with payback under 6 years.
Common pitfalls in BESS sizing
Three sizing errors recur on Irish commercial BESS quotes:
- Using nameplate kWh instead of usable kWh at end of warranty. A 1,000 kWh nameplate LFP system typically delivers 920–950 kWh at year zero (95% DoD floor) and falls to 720–800 kWh by year 10 (80% capacity retention warranty). Build your business case on the year-10 number, not the badge.
- Forgetting auxiliary draw against contracted kWh. Cabinet HVAC, BMS controller, fire panel and EMS gateway typically consume 1,500–4,500 kWh/year per 500 kWh installed in Irish climate. Over a 15-year life this is 30,000–70,000 kWh of "ghost" import that erodes arbitrage margin. Always confirm whether the throughput warranty deducts auxiliary load or counts only delivered kWh.
- Ignoring ESB Networks MIC import headroom. Charging a 500 kW PCS at 500 kW from grid adds 500 kVA to your maximum demand window. On a site with a 600 kVA MIC and 300 kW baseload, this triggers an MIC upgrade (€8k–€35k) unless you cap charging power in the EMS to (MIC - baseload) × 0.9.
The one-sentence rule
If you remember nothing else: kW sizes the peak you can hit, kWh sizes how long you can hold it for, and you must size both for the worst-case event in your 12-month half-hourly profile - not the average.
Get 3 free commercial battery quotes — free and no obligation.
Frequently asked questions
What is the difference between kW and kWh in a battery?
kW (kilowatts) is the rate of power flow in or out of the battery, set by the inverter (PCS). kWh (kilowatt-hours) is the total energy stored in the cells. A 100 kW / 200 kWh battery delivers 100 kW for 2 hours. You need both numbers to evaluate a commercial BESS quote.
What is C-rate in a commercial battery?
C-rate is the ratio of power to capacity. A 1C battery discharges fully in 1 hour, a 0.5C battery in 2 hours, a 2C battery in 30 minutes. Most Irish commercial BESS are 0.25C-1C systems matched to peak shaving and DS3 applications.
Which matters more, kW or kWh, for Irish peak shaving?
Both - and they must match your peak event profile. You need enough kW to shave the peak height, and enough kWh to cover the peak duration. A 90-minute evening peak needs at least 1.5 hours of usable energy at the desired shave power.
Can I add more kWh later without replacing the PCS?
Sometimes, if the PCS and EMS are sized with expansion headroom and the racks share a common DC bus. Most Sungrow PowerStack, Tesla Megapack and BYD MV cabinets support modular expansion within the same lineup, but a retrofit is rarely cheaper than oversizing on day one.
How do I size a BESS for an Irish factory?
Pull 12 months of half-hourly load data from ESB Networks via your supplier. Identify the top 50 peak events and their durations. Size kW to shave the peak you want to remove, and kWh to cover the longest of those events with 15-20% degradation headroom.
Sources & further reading
- ESB Networks Load Profile Data — ESB Networks
- SEAI Energy Statistics in Ireland — SEAI