Heat Pumps for Irish Care Homes and Nursing Facilities

Irish nursing homes face a unique heat pump design challenge: high indoor temperatures, infection control, 24/7 occupancy and tight HIQA compliance. Here is how the projects work in 2026.

By Smart Solar Editorial · Updated 18 May 2026 · 11 min read

The toughest commercial heat pump design problem in Ireland

Care homes and nursing facilities present a design brief that pushes commercial heat pump technology harder than any other Irish commercial segment. The combination of:

  • Continuous 24/7/365 occupancy with no shutdown window for plant works
  • High maintained indoor temperatures — HIQA Standard 25.1 requires 21–24 °C in resident areas
  • Heavy DHW demand for bathing, laundry and infection control
  • Infection control protocols that constrain ductwork sharing
  • Acoustic limits from a vulnerable resident population
  • Resilience requirements — heating failure is a HIQA notifiable incident

…makes care home heat pump retrofit one of the most demanding commercial briefs an Irish MEP consultant can pick up. It is also one of the most rewarding: the Irish nursing home estate consumes roughly 220 GWh of heating fuel annually, mostly oil and LPG, with delivered costs 50–90% above mains gas.

HIQA temperature requirements drive the design

HIQA's National Standards for Residential Care Settings for Older People (Standard 25.1) requires "a comfortable temperature" maintained at 21–24 °C in resident living areas, with 24 °C in bathrooms and 22 °C minimum in bedrooms overnight. These are higher than typical commercial office targets and have three design consequences:

  1. Higher heating load per m² than offices — typically 60–95 W/m² for an Irish care home versus 35–55 W/m² for a modern office
  2. Smaller temperature delta across emitters — with rooms at 22 °C and flow at 45 °C, the delta is only 23 °C versus 40 °C in a 5 °C office at start-up
  3. Longer continuous operation — the heat pump runs at 30–80% load for 18+ hours daily during the heating season

Practical implication: the heat pump must be sized for steady-state load with very modest weather-compensation roll-back, and emitter surface area must be generous.

Plant resilience and N+1 redundancy

HIQA inspectors treat a heating failure as a notifiable safety event. This effectively mandates N+1 redundancy on care home heat pump plant:

  • Two heat pumps each sized to 60–70% of design load, configured in parallel, so single unit failure still delivers 60% capacity
  • Electric back-up boiler sized to 100% of design load, for catastrophic refrigeration plant failure
  • UPS-backed controls to ensure heating continues through short power interruptions
  • Diesel generator backup at site level for ≥24 hour island operation

The N+1 requirement adds typically 25–35% to nominal heat pump capex but is non-negotiable on HIQA-registered settings.

DHW design under infection control

Irish care home DHW design is tightly constrained by HSE infection control guidance:

  • 60 °C minimum at storage, 50 °C minimum at every outlet (legionella control)
  • Weekly thermal disinfection cycle to 70 °C at dead-leg outlets
  • Anti-scald TMV2 valves at every patient outlet limiting delivery to 41 °C
  • Separation of patient and clinical DHW circuits

These constraints favour either an R290 high-temperature heat pump (delivering 70 °C single-stage) or a buffer-tank pre-heat plus electric pasteurisation top-up. The R290 option has gained ground rapidly in Irish care home projects through 2024–2026 because it eliminates the SCOP penalty of electric resistance heating during the legionella cycle.

Typical sizing for Irish care homes

Indicative capacity for common Irish care home sizes:

  • 40-bed single-storey nursing home, 1,800 m²: 110–150 kW heat pump system
  • 60-bed two-storey nursing home, 2,800 m²: 180–230 kW heat pump system
  • 100-bed campus, 4,500 m²: 280–380 kW heat pump system
  • 150-bed dementia care campus, 6,500 m²: 400–520 kW heat pump system

DHW typically adds 25–40% to nominal space heating capacity for nursing homes, versus 15–25% for offices.

2026 installed pricing

Indicative installed pricing for Irish care home projects:

  • 40-bed home, 130 kW system: €120,000–€200,000 installed
  • 60-bed home, 200 kW system: €170,000–€280,000 installed
  • 100-bed campus, 320 kW system: €260,000–€430,000 installed
  • 150-bed campus, 450 kW system: €380,000–€620,000 installed

These figures assume N+1 redundancy, R290 DHW, and full HSE-compliant pipework. They exclude any fabric upgrades that may be needed to bring the building to a BER B suitable for heat pump operation.

EXEED is particularly generous to care homes

EXEED grant assessments favour projects with high baseline carbon intensity and high annual operating hours. Care homes score well on both metrics — they typically run 8,500+ heating hours per year versus 2,200 for offices, and most are still on oil or LPG with carbon intensities 30–60% above mains gas.

Typical EXEED grant capture on Irish care home projects in 2024–2026:

  • Oil-replacement projects: 28–30% of eligible capex
  • LPG-replacement projects: 27–30% of eligible capex
  • Gas-replacement projects: 22–28% of eligible capex (lower carbon delta)

A 100-bed care home replacing oil heating typically captures €75k–€130k in EXEED grant against a €260k–€430k project, with the balance further reduced 12.5% by ACA capital allowance.

Acoustic and resident wellbeing

Care home heat pump installations face tighter acoustic constraints than any other commercial segment:

  • 40 dB(A) target at nearest bedroom window
  • 35 dB(A) overnight target where bedrooms face the plant area
  • No tonal noise components (no audible compressor whine)

Practical implications:

  • Specify inverter-driven scroll compressors, not on-off reciprocating
  • Use acoustic enclosures (typically 4–8 dB(A) reduction)
  • Place outdoor units away from bedroom-facing facades
  • Schedule defrost cycles outside resident sleep hours

Case studies — Irish care home heat pump projects

  • Mowlam Healthcare estate (Tipperary, Limerick, Cork): 280–420 kW R290 systems across three homes, commissioned 2024–2025
  • Beneavin House Dublin: 320 kW air-to-water plus R290 DHW, replacing 1990s oil system, 62% reduction in heating energy
  • Bartra Healthcare new-build campuses: NZEB compliant ground-source designs, typically 250–400 kW per campus
  • Virtue Integrated Elder Care, Cork: 180 kW heat pump retrofit on 2003 LPG-heated home

Practical procurement guidance

For any Irish care home considering heat pump conversion:

  1. Document baseline performance first. HIQA will want before-and-after temperature compliance evidence.
  2. Insist on N+1 redundancy in tender. Single-unit designs are not HIQA-compliant.
  3. Specify R290 DHW or buffer-plus-electric pasteurisation. Direct 60 °C from air-source kills SCOP.
  4. Plan installation around peak occupancy. Avoid winter months. Most Irish care home retrofits run April–September.
  5. Run a 4-week shadow operation with old and new plant available in parallel before decommissioning legacy boilers.

Care home heat pump projects in Ireland are technically demanding but financially highly attractive — typical post-grant, post-tax payback ranges from 3.5 to 5.5 years on oil and LPG replacement, with a 20-year NPV materially better than any other heating option.

Get 3 free commercial heat pump quotes — free and no obligation.

Frequently asked questions

What temperature does an Irish care home need to maintain?

HIQA Standard 25.1 requires 21–24 °C in resident living areas, 24 °C in bathrooms, and 22 °C minimum in bedrooms overnight. These targets drive a higher design load (60–95 W/m²) than offices and require generous emitter surface area to operate well with heat pump flow temperatures.

Is N+1 redundancy required for care home heat pumps?

Effectively yes. HIQA treats heating failure as a notifiable safety incident, so the standard configuration is two heat pumps each sized to 60–70% of design load, an electric backup boiler sized to 100% of load, UPS-backed controls and site-level diesel generator backup.

How are legionella controls handled with a heat pump?

Two main options: an R290 high-temperature heat pump that delivers 70 °C single-stage and runs weekly pasteurisation directly, or a buffer-tank pre-heat with electric immersion top-up to 65 °C for legionella cycles. R290 typically delivers SCOP 0.3–0.5 better and is now the preferred specification for new Irish care home projects.

What payback do Irish care homes see on heat pump retrofit?

Typical post-grant, post-tax payback is 3.5–5.5 years on oil replacement, 3–5 years on LPG replacement, and 5–7 years on mains gas replacement. EXEED capture is unusually strong on care homes (28–30% of eligible capex) because of high baseline carbon intensity and long annual operating hours.

Sources & further reading