LPHW vs VRF Commercial Heat Pump Systems
LPHW or VRF? The single biggest architectural choice on any Irish commercial heat pump project. Here is when each wins on capex, operating cost and 25-year serviceability.
By Smart Solar Editorial · Updated 18 May 2026 · 11 min read
The architectural fork in the road
Every Irish commercial heat pump project hits the same fork at concept stage: distribute heat as LPHW (low-pressure hot water, typically 40–55 °C) or as VRF (variable refrigerant flow, refrigerant in copper pipework throughout the building)?
The decision drives everything downstream — capex, operating cost, refurbishment flexibility, maintenance regime, F-gas exposure, and tenant fit-out cost. Getting it wrong locks in 25 years of suboptimal operation. Getting it right delivers efficient, serviceable, future-proof heat distribution for the life of the building.
This article walks through the trade-offs explicitly so the decision is made on merit rather than habit.
The two architectures explained
LPHW (Low-Pressure Hot Water)
A central heat pump heats water to 40–55 °C. The hot water circulates through insulated steel or copper pipework to:
- Radiators in offices, hotels, care homes
- Underfloor heating in newer construction
- Fan coil units (FCUs) for spaces requiring cooling capacity
- Heat exchangers at sub-system level
Dominant architecture for: care homes, hotels, schools, hospitals, large commercial buildings with central plant rooms.
VRF (Variable Refrigerant Flow)
Multiple outdoor refrigerant compressor units feed a network of indoor evaporator units via refrigerant copper pipework. Each indoor unit (typically ceiling cassette or ducted) controls a zone of the building. Heat pump cycle operates directly between outdoor and indoor units; no intermediate water circuit.
Dominant architecture for: multi-tenant offices, mid-size hotels, retail, mixed-use commercial.
Capex comparison — same building, two architectures
Worked example: 3,000 m² Dublin office, 180 kW heating load with cooling capability.
LPHW with air-to-water heat pump and fan coils
- Air-to-water heat pump (Carrier 30XB or Vaillant): €110,000
- Buffer tanks (2 × 4,000 L stratified): €25,000
- Primary pipework, valves, hydraulic separator: €35,000
- Secondary distribution pipework (steel insulated): €85,000
- Fan coil units (45 × 4 kW units): €68,000
- Controls and BMS integration: €30,000
- Plant room civils, acoustic, electrical: €60,000
- Commissioning and F-gas: €15,000
- Total LPHW installed: €428,000
VRF with Daikin VRV 5 or Mitsubishi City Multi R2
- VRV 5 outdoor units (2 × 95 kW): €85,000
- Indoor units (40 × ceiling cassettes 5–6 kW): €72,000
- Refrigerant pipework, branch boxes: €58,000
- Controls and BMS integration: €38,000
- Plant room civils (smaller footprint), acoustic, electrical: €42,000
- Commissioning and F-gas: €18,000
- Total VRF installed: €313,000
Capex delta: VRF is approximately 27% cheaper for this configuration. The VRF saving comes primarily from avoided secondary pipework (no large insulated steel pipes) and integrated indoor unit cost.
This ~25% capex advantage for VRF is typical for office configurations in the 150–400 kW range. For projects above 400 kW or below 100 kW, the calculus often shifts.
SCOP comparison
LPHW at W45
- Heat pump primary SCOP: 3.6–4.0 (Tier-1 air-to-water at W45)
- Distribution losses: 5–10% of delivered heat
- System SCOP delivered to point of use: 3.2–3.7
VRF at refrigerant-side distribution
- Heat pump SCOP at indoor unit: 3.6–4.0 (Tier-1 VRF)
- No water distribution losses (refrigerant transfers latent heat at saturation)
- System SCOP delivered to point of use: 3.6–4.0
VRF typically delivers slightly better real-world system SCOP because there are no water-circuit distribution losses. The advantage is 0.2–0.4 SCOP, equating to roughly 6–11% lower operating cost in well-designed systems.
OPEX comparison
For the 3,000 m² Dublin office example (annual heating energy 380,000 kWh):
LPHW operating cost
- System SCOP 3.4
- Annual electricity: 111,800 kWh
- @ €0.22/kWh: €24,600/year heating cost
VRF operating cost
- System SCOP 3.7
- Annual electricity: 102,700 kWh
- @ €0.22/kWh: €22,600/year heating cost
OPEX delta: VRF approximately 8% cheaper to run. Over 25 years at 2% real escalation, this is approximately €60,000 of NPV advantage to VRF.
Where LPHW wins
VRF wins on capex and slightly on OPEX, but LPHW wins decisively on several fronts:
1. Refurbishment flexibility
Tenant fit-out and space repurposing on LPHW is trivial — radiators and FCUs can be moved, added, removed without touching the primary plant. VRF refurbishment requires refrigerant work, F-gas registered installer attendance and recommissioning. For multi-tenant office stock with high churn, LPHW's flexibility is a major operational advantage.
2. F-gas exposure
VRF systems hold 10–40 kg of refrigerant per system. LPHW systems hold 2–8 kg in the central heat pump only. EU F-gas Regulation 2024/573 service refrigerant pressure, leak testing burden and end-of-life decommissioning cost all scale with refrigerant inventory. LPHW reduces lifetime F-gas exposure 70–85%.
3. DHW integration
LPHW systems integrate DHW production naturally through a calorifier or stratified buffer. VRF DHW requires a separate water-cooled heat pump or significant ancillary plant, adding 15–25% to project capex if DHW is a meaningful load.
4. Industrial process heat
For pharma, food and beverage manufacturing requiring 65–95 °C process heat, only LPHW with high-temperature heat pumps (Carrier 61XW, Vaillant aroTHERM plus R290) can deliver. VRF cannot reach high process temperatures.
5. Long pipe runs
Large or tall buildings exceed VRF refrigerant pipework limits (165 m total length, 50 m vertical separation). LPHW pipework can run much longer distances without performance penalty.
6. Mixed building stock
Where a single plant serves multiple buildings (campus, district scheme), LPHW is the only practical architecture. VRF cannot economically span between separate building structures.
Where VRF wins
VRF wins on:
1. Multi-zone control flexibility
Each VRF indoor unit is independently controllable, allowing desk-level temperature control. Particularly valuable for multi-tenant offices and mixed-use buildings where lease structures require zone-level metering.
2. Simultaneous heating and cooling
Heat recovery VRF (Daikin VRV 5 Heat Recovery, Mitsubishi City Multi R2) captures heat from cooling zones and uses it in heating zones. For buildings with diverse simultaneous demand (perimeter heating + core cooling), this delivers SCOP 4.0+ in field operation.
3. Lower capex on mid-size office
For 100–400 kW office projects, VRF typically saves 20–30% on capex. The saving compounds across multiple buildings in a portfolio.
4. Refurbishment retrofit
Retrofitting VRF into existing buildings is often easier than retrofitting LPHW because VRF needs much smaller distribution pipework (slim copper rather than insulated steel).
5. Plant room space saving
VRF central plant room is typically 40–60% smaller than equivalent LPHW because most equipment is outdoor.
Hybrid approaches
Many Irish commercial projects use hybrid architectures:
- LPHW backbone + VRF for office floors: central plant for DHW and base heating, VRF for tenant zone control
- LPHW for perimeter + air-air for core: radiators or UFH for perimeter zones, ducted air for internal zones
- VRF for heating + LPHW for DHW: VRF cannot do DHW efficiently, so DHW is decoupled
Hybrid architectures often deliver the best technical solution but at modestly higher complexity and capex than either pure-play approach.
Decision matrix
| Building characteristic | Architecture |
|---|---|
| Multi-tenant office, < 400 kW | VRF |
| Large hotel with major DHW | LPHW |
| Care home (HIQA, infection control) | LPHW |
| School (DoE Pathfinder spec) | LPHW |
| Hospital | LPHW |
| Leisure centre (pool heat pump duty) | LPHW |
| Warehouse with destratification | LPHW |
| Mixed-use mid-rise | Hybrid |
| Multi-building campus | LPHW |
| Industrial process heat | LPHW with high-temp HP |
| Heritage building (minimal pipework) | VRF |
| Data centre with heat recovery | LPHW |
Final word
For most Irish commercial heat pump projects in 2026, the architectural choice is more nuanced than "VRF for offices, LPHW for everything else". Multi-tenant office and retail favour VRF; institutional, healthcare, hospitality and industrial applications favour LPHW. Mixed-use deserves hybrid consideration.
The wrong decision is locked in for 25 years and costs five-to-seven figures over the asset life. The right decision delivers efficient, serviceable, future-proof heating for the life of the building. Make the decision deliberately, not by default.
Get 3 free commercial heat pump quotes — free and no obligation.
Frequently asked questions
Is VRF cheaper than LPHW for Irish commercial buildings?
For 100–400 kW office projects, VRF typically saves 20–30% on capex. Above 400 kW or where DHW is a major load, LPHW with central plant becomes more competitive. For hotels, care homes, schools and leisure centres LPHW is usually preferable on lifetime economics despite higher upfront capex.
Which has better SCOP — LPHW or VRF?
VRF typically delivers 0.2–0.4 better system SCOP because there are no water-circuit distribution losses. The OPEX advantage is roughly 6–11% in well-designed systems. However, LPHW systems with very low flow temperatures (W35 underfloor) can match or beat VRF on SCOP.
Can VRF handle domestic hot water?
Not efficiently. VRF systems are optimised for space heating and cooling at relatively low water-side equivalent temperatures. DHW at 60–65 °C requires either a separate water-cooled heat pump or significant ancillary plant, adding 15–25% to project capex. Hotels, care homes and leisure centres with meaningful DHW load typically need LPHW.
How long can VRF pipework runs be?
Daikin VRV 5 supports 165 m total pipe length, 50 m vertical separation, 90 m furthest indoor unit. Mitsubishi City Multi R2 extends to 250 m total length. Buildings exceeding these limits — typically over 15 floors or sprawling campus configurations — require LPHW central plant instead.